Community

Forum archive

Threads from the old Audio Innovate forum.

Rane TTM-54 with the Innofader Pro



Rane TTM54 Installation Instructions

EDIT 2/5/2012 by Elliot Marx admin the below instructions also work for the TTM52!

 

EDIT 2/19/2016 for the Innofader Pro2, in step 15, please use adapter (15) from the Innofader Pro2 kit. Otherwise the instructions are pretty much the same.

STEP 1: Remove the 6 screws shown here, then remove the crossfader and faceplate.
Rane54_Innofader01.jpg



STEP 2: Remove the 11 screws shown here, and the 2 nuts around the gain knobs.
Rane54_Innofader02.jpg



STEP 3: Carefully unhook attached cables and remove the top-plate from the base of the mixer. Make sure to note where all cables go.
Rane54_Innofader03.jpg



STEP 4: Remove the 4 screws shown here, and the nut around the headphone jack.
Rane54_Innofader04.jpg



STEP 5: Carefully remove the PCB (printed circuit board) from the mixer and turn it over. Note the pin solders circled here.
Rane54_Innofader05.jpg



STEP 6: Find the 3-wire (Red-Black-Red) cable that came with your Innofader.
Rane54_Innofader06.jpg



STEP 7: Cut the plug off of one end of the cable and strip the 3 wires.
Rane54_Innofader07.jpg



STEP 8: Solder the wires to J22 on the Rane PCB as follows:
Pin 10 +15V -> Red wire
Pin 13 GND -> black wire
Pin 12 -15V -> other red wire.
It doesn't matter which red wire is connected to +15V and which is connected to -15V as long as they are 2 separate wires!
Rane54_Innofader08.jpg

 

***For Rane 52 users, the hookup is the same but the PC board looks slightly different as such:

Rane52_PCB.JPG


STEP 9: The power cable is complete. Now find the Molex 8-pin to IDC 10-pin crossfader cable that came with your Innofader.
Rane54_Innofader09.jpg



STEP 10: Follow these instructions and diagram for modifying the cable.
Inno_Rane54_cable_diagram_V4.jpg



STEP 11: Screw the PCB back into the mixer and locate the 6 pins circled here.
Rane54_Innofader17.jpg



STEP 12: Plug in your new crossfader cable as shown. (You will only be using 6 of the 10 holes in the IDC connector.)
Rane54_Innofader18.jpg



STEP 13: Find the Pioneer crossfader plate that came with your Innofader.
Rane54_Innofader11.jpg



STEP 14: Using the crossfader plate as a guide, mark the two outer holes on your mixer, then drill new holes.
(You can't use the existing Rane holes because the screws will touch the sides of the Innofader, causing grounding problems.)
Also, in order for the screws to sit flush, counter sink the holes.
Rane54_Innofader12.jpg



STEP 15: Put the top-plate back on the mixer. (Make sure not to crush any of the LEDs.)
Plug all cables into their original locations. Hook up the new power and crossfader cables as shown.
Rane54_Innofader13.jpg



STEP 16: Adjusting the Innofader properly may take a bit of trial and error. I've found these settings work well.
Rane54_Innofader14.jpg



STEP 17: Attach the faderplate to the Innofader, then screw the faderplate into the mixer.
(You can use self tapping sheet metal screws or just use a nut on the inside of the mixer.)
Rane54_Innofader15.jpg



STEP 18: Put faceplate back on, and most importantly, ADD YOUR INNOFADER DECAL!!!
Rane54_Innofader16.jpg



STEP 19: Enjoy your Innofaded 54